<![CDATA[TCP Control of Projector on/off]]>Hi All


I am currently working on a project that needs me to be able to control turning 8 Espon EB700U projectors on and off using Isadora. Ive read up and seen that TCP actors should be able to do that. However I have no idea where to start with writing the code for the TCP actor. I have looked at a couple of previous forum posts about it to do with Panasonic projectors but I am still not sure what code to put in to make them work. If anyone could assist me or direct me to somewhere that could give me more information to help me with this it would be greatly appreciated.

Thanks

Andy

]]>https://community.troikatronix.com/topic/5547/tcp-control-of-projector-on-offRSS for NodeSat, 16 May 2026 21:10:29 GMTSun, 14 Oct 2018 16:57:45 GMT60<![CDATA[Reply to TCP Control of Projector on/off on Thu, 18 Oct 2018 09:33:31 GMT]]>@juriaan

I was just testing and playing around on the patch you sent me. I copied and pasted the actor in the patch.

@jhoepffner 

They had DHCP on so had the same subnet and ip class on the same network. 
I will be testing it again later today to see if it was something stupid on my side.

Thanks

Andy

]]>https://community.troikatronix.com/post/32527https://community.troikatronix.com/post/32527Thu, 18 Oct 2018 09:33:31 GMT<![CDATA[Reply to TCP Control of Projector on/off on Tue, 16 Oct 2018 05:49:24 GMT]]>@andy-delmaine

Are you sure you made a proper adhoc network, with computers and beamer sharing the same class of address, like 192.168.1.XXX and the same network mask, 255.255.255.0 in a private network? I use sometime PJLink with 4 Panasonic beamers and it works perfectly.

Jacques

]]>https://community.troikatronix.com/post/32494https://community.troikatronix.com/post/32494Tue, 16 Oct 2018 05:49:24 GMT<![CDATA[Reply to TCP Control of Projector on/off on Mon, 15 Oct 2018 22:33:51 GMT]]>Hi there @Andy-Delmaine 

I tried it with the Test Software and it seems that it works correctly here. Could you upload your patch so I can get some more information regarding your setup ?

With kind regards,

Juriaan

]]>https://community.troikatronix.com/post/32492https://community.troikatronix.com/post/32492Mon, 15 Oct 2018 22:33:51 GMT<![CDATA[Reply to TCP Control of Projector on/off on Mon, 15 Oct 2018 06:19:13 GMT]]>@andy-delmaine

Hi there,


Never tried it with two projectors before. Will test it out tonight and let you know.


- Juriaan

]]>https://community.troikatronix.com/post/32478https://community.troikatronix.com/post/32478Mon, 15 Oct 2018 06:19:13 GMT<![CDATA[Reply to TCP Control of Projector on/off on Sun, 14 Oct 2018 23:52:09 GMT]]>Hi @juriaan

When I said it was working perfectly that was only with one projector, but when I tried it with 2 projectors I couldn't seem to get it working. I tried changing the stream IDs and trying both different IPs and the same IPs but couldnt get it to send to both. the original projector I tried works fine and the second one works fine on the original actor but when I have 2 of the PJlink actors I couldn't seem to get it working. I also tried changing ports or buffer size just to see if it did anything, but it didnt help getting them working.


Any help is appreciated

Thanks

Andy

]]>https://community.troikatronix.com/post/32474https://community.troikatronix.com/post/32474Sun, 14 Oct 2018 23:52:09 GMT<![CDATA[Reply to TCP Control of Projector on/off on Sun, 14 Oct 2018 22:07:32 GMT]]>Regarding your actor questions :


If you wish to turn off the projector :

Command = POWR

Body = 0

If you wish to turn on the projector :

Command = POWR 

Body = 1

If you wish to ask about the "POWR" state (So is the Projector On or Off)

Command = POWR

Body = ?

]]>https://community.troikatronix.com/post/32473https://community.troikatronix.com/post/32473Sun, 14 Oct 2018 22:07:32 GMT<![CDATA[Reply to TCP Control of Projector on/off on Sun, 14 Oct 2018 21:51:46 GMT]]>@juriaan

Hi 

I found out why it wasn't working i took the 0's out of the IP address and it worked and its all working perfectly 

Thank you so much

Andy

]]>https://community.troikatronix.com/post/32472https://community.troikatronix.com/post/32472Sun, 14 Oct 2018 21:51:46 GMT<![CDATA[Reply to TCP Control of Projector on/off on Sun, 14 Oct 2018 21:39:19 GMT]]>@juriaan

Hi,

Thanks a lot for this! I've got one issue I am not getting connection state 2. I only get connection state 1. What does this mean and how can i fix it. Also the 'body' input has a question mark in. Do i need to put something else in there? I set the PJlink Password on the projector to ABC.

Attached is IP address of the projector and what I've put into the actor, please let me know what I've done wrong.

Thanks

]]>https://community.troikatronix.com/post/32471https://community.troikatronix.com/post/32471Sun, 14 Oct 2018 21:39:19 GMT<![CDATA[Reply to TCP Control of Projector on/off on Sun, 14 Oct 2018 19:35:18 GMT]]>@andy-delmaine said:

Espon EB700U

 Hi there @Andy-Delmaine,

Welcome to the Isadora Community forum. The projector that you listed above has PJLINK support (A protocol to connect beamers using Ethernet). 

Please refer to the following post regarding my Tutorial about PJLINK and the necassary actors to make it work with Isadora.

https://community.troikatronix...

If you have any questions, feel free to make a new post or send me an email at hello@juriaan.me.

With kind regards,

Juriaan

]]>https://community.troikatronix.com/post/32469https://community.troikatronix.com/post/32469Sun, 14 Oct 2018 19:35:18 GMT