Single Desktop -control screen ideas

PatrickPagano

Is this something that could be addressed if we crack open the SDK?

Perhaps a special multi-screen projector actor?

keftaparty

Hi Patrick,

Maybe I missunderstand a bit what you want, but if I understand well, what you need is:

In catalyst drivers ( I have no ati machine running, so names are going to be aproximative):

-Set all your screens independent

-Then make a catalyst group with screens 2>6 ( 6400x1024 ) that isadora will recognise as your screen n°2

So you keep screen1 for patching/control

best

Mehdi

PatrickPagano

It won't seem to let me do that. When i try to create what you are suggesting and i have tried several ways which is a

5x1+1 setup it always disables the +1 monitor which is super frustrating. So i am thinking about other solutions

thank you for your thoughtful reply though Mehdi

Patrick

LPmode

you may need to create different configurations, perhaps 3 screens 2x wide. or 2 screens 3x wide. that way you can set one of the screens to how stages on the available subdivisions so you have a clear section available for the interface.otherwise you may need to set preview window to your 5x wide desktop. do force preview and then move the window in place. you'll have to set lower resolutions and deal with the window borders tho and perhaps a performance hit.

Skulpture

Hi @PatrickPagano

My reply via email was very similar to @[keftaparty](http://troikatronix.com/troikatronixforum/profile/7/keftaparty) idea.

Really you need each screen to be independent rather than one long extended desktop. Then you can control each one.

Have you found a solution/work around yet?

keftaparty

Hi,

I would really not recommand setting 6 different screens into catalyst.

Under windows isadora takes a HUGE amount of ressource to deal with multiple stages on multiple screens.

@[PatrickPagano](http://troikatronix.com/troikatronixforum/profile/832/PatrickPagano) : I would dig a bit into catalyst, sometimes setting the groups is tricky.

By the way, if you're on a ivybridge machine, isn't it possible to use the intel HD chip for your control monitor ? ( never tried it with isadora )

mark

Basically, what he needs is the TripleHead2Go (left/mid/right) feature but for in sixths instead of thirds. This was the response I wrote to him privately this morning:

_There is no perfect solution.

The Stage Preferences allow you to specify which third of the screen will be used for a stage – this is to support the Matrox TripleHead2Go. Now, if you go to the stage preferences, and set it up as shown in the attached picture, you'll end up with two stages: one covering outputs 3 + 4, and one covering outputs 5 + 6. The first third would have nothing, allowing you to see your document.

To be able to divide this into sixths, I'll need to modify the program. And that's not something I can promise immediately.

Is there room for one more card in your machine? Get a cheap-o card with one output for the User Interface? That's the immediate solution I'm afraid.
_
Best Wishes,
Mark

PatrickPagano

Hi Everyone and thanks as always for the thoughtful and innovative ideas regarding Isadora.

I actually was thinking about as Mark also suggested adding a low-cost Nvidia GT card into the machine and now have Catalyst running a 5X1 configuration @ 8000x1200 as one single desktop and the Nvidia Card acting as my control screen. This will make shows MUCH more easy.

keftaparty

Hi Patrick,

I was allways told that ATI + NVidia drivers have big problems to run besides.

I think you should better buy a second ATI.

Don't you have a Ivy bridge CPU ?

Best

Mehdi

PatrickPagano

i tested them today and they worked fine together. I guess i could install another ATI card but i really did not want to place another eyefinity into the machine just for a control monitor but i guess if i could put it into crossfire it miugt be worth it. What problems have you heard about Mehdi?