DMX In Enttec

Skulpture

Thanks fifou :)

pierremine

OK je vais écrire en français si quelqu'un peut traduire :)

je voudrais récupérer les infos DMX qui arrive via l'enttec dans isadora pour contrôler des patch....

voilà

Skulpture

Je pense que un bon endroit pour commencer est de télécharger ces acteurs isadora de l'ancien forum:

[http://forum.troikatronix.com/cgi-bin/forum/gforum.cgi?post=9813;search_string=Enttec%20Lanbox%20MATRIX;t=search_engine#9813](http://forum.troikatronix.com/cgi-bin/forum/gforum.cgi?post=9813;search_string=Enttec%20Lanbox%20MATRIX;t=search_engine#9813)

J'espère que cela va vous aider.

Les acteurs peuvent envoyer et recevoir des données à partir de la boîte Enttec.

-----

I think a good place to start is downloading these isadora actors from the old forum:

http://forum.troikatronix.com/cgi-bin/forum/gforum.cgi?post=9813;search_string=Enttec%20Lanbox%20MATRIX;t=search_engine#9813

Hopefully this will help you.

The actors can send and recieve data from the Enttec box.

pierremine

Super ca marche merci petit récap sur mon site:) http://www.lesloupiotes.fr/wordpress/?p=503

fifou

Translation from pierremine's answer:
Great, it works ! Here's a summup on my site (in french) : http://www.lesloupiotes.fr/wordpress/?p=503

(Dommage le lien pour le user actor ne fonctionne pas !)
Du coup on ne sait pas comment tu fais !

Philippe

pierremine

oups lien corriger !!!

DusX

I have started working on adding DMX IN to my actor, but haven't had a chance to finish.. sorry.

gunther

To get the "DMX in" values of the Enttec dmx usb pro, you have to use the serial in watcher. To activate the correct serial input, go to "Communications->Serial Setup" and make the assignment between COM port and Isadora's serial port (i.e. connect COM3 to Port 1). Afterwards, turn on the serial communication by "Communications->Enable Serial Ports".

The difficulty is to extract the the DMX values from the input stream. After a couple of experiments i found the solution, thanks to the new monitor function in the pre-release version. You findworking examples in the attached file.

Here are working examples for the stream parser:
Get DMX1 and DMX2: { e7 7e 05 } 4 byte dmx1 : int = 1byte dmx2 : int = 1byte
Get DMX8: { e7 7e 05 } 4 byte 7byte dmx8 : int = 1byte
Get DMX512: { e7 7e 05 } 4 byte 511 byte dmx512 : int = 1byte

Good luck, Gunther
eaab25-test-serial.izz

fubbi

Gunther thats some seriously cool stuff. Do you think the same applies to the Lanbox?

CraigAlfredson

I'm pretty sure that code is specific to the Enttec. There are instructions on how to do DMX in on the Lanbox somewhere on the old forum.

Craig

gunther

I think with the lanbox it's quite easy. You can configure the Lanbox with LCedit, Tools->Global Settings->DMX. Then the Lanbox maps DMX input channels to light channels. With the regular Lanbox command ChannelReadData (see Reference manual of the Lanbox) you get the DMX input values as channel values.

You will find a lot of Isadora actors of Lanbox commands, including the ChannelReadData, here:
http://troikatronix.com/troikatronixforum/discussion/134/actors-for-using-the-tcp-connection-of-the-lanbox#Item_7

I'm pretty sure that gives a solution.
Gunther

fubbi

cool beans. I am working on a project which has a grand MA desk controlling isadora. I would like to dig deeper and understand more about the TCP actor and lanbox.