Artnet limits

Troubleshooting and Bug Reports
Log in to reply
  • Juriaan
    Beta Platinum

    Hi there,

    Is it true that Izzy can only send 4 ports out ? So that means that you can only send 4 universes ? Why cant it use a full subnet (16 universes) ?

    - Juriaan

    0 bonemap mark 2 Replies
  • bonemap
    Beta Platinum

    @juriaan said:

    Is it true that Izzy can only send 4 ports out

    Hi, 

    That does not sound right. "This actor represents an ArtNet "node." Each node has something called an ArtNet "subnet" address, which can range from 0 to 15". Check out the knowledgebase article here. 

    best wishes

    bonemap 

    0
  • mark

    @juriaan said:

    Is it true that Izzy can only send 4 ports out ? So that means that you can only send 4 universes ? Why cant it use a full subnet (16 universes) ?

    This is a limitation of Art Net itself with regard to each IP address. For example, see this note on GitHub about a another Art Net plugin.

    ArtNet limits a single device (identified by a unique IP) to four input and four output ports, each bound to a separate ArtNet Port Address (see the ArtNet spec for more details). The ArtNet Port Address is a 16 bits int, defined as follows:

    If you use a second ethernet/wifi interface with a unique IP, then you can have more.

    Best Wishes,
    Mark

    1 bonemap Juriaan 2 Replies
  • bonemap
    Beta Platinum

    @mark said:

    This is a limitation of Art Net itself with regard to each IP address

    Hi,

    OK - that is good to know.

    cheers,

    bonemap

    0
  • Juriaan
    Beta Platinum

    @mark

    May I ask why Resolume is fully capable of sending more then 4 universes?

    0 mark 1 Reply
  • mark

    @juriaan said:

    May I ask why Resolume is fully capable of sending more then 4 universes?

    Well, upon further research, I guess that's because they support ArtNet 4. (See here.)  I used open source code to implement the ArtNet modules, and apparently that code is ArtNet 3, which has the four port limit. I'll look into what it will take to update the code and publish an update to the plugins.

    I am using libartnet, which is older and is ArtNet 3. But even the latest open source code from the OLA (Open Lighting Association) doesn't support ArtNet 4, as seen by this open issue on their GitHub repro. 

    Best Wishes,
    Mark

    0 I 1 Reply
  • I
    Beta Platinum

    @mark

    Hi Mark, I'd happily test a trial a trial at any point if you'd like >4 universe test --   I'm in mid-build on a large artnet based LED pixel installation that uses 16 universes.

    Cheers, Ian

    2 Woland 1 Reply
  • Woland
    Tech Staff

    @ian

    Please make a showcase post if/when you've documented your installation. I'm sure lots of folks, including myself, would love to see it!

    Best wishes,

    Woland

    0
  • I
    Beta Platinum

    Hi Woland, I'll definitely post some documentation when all is public. For people in the NYC area it'll premiere at EMPAC in Troy, NY the second week of Sept. 2018. And putting in a plug for the good folks of DMXking and their LeDMXPro boxes which have been very helpful.

    3 bonemap 1 Reply
  • bonemap
    Beta Platinum

    @ian said:

    DMXking and their LeDMXPro boxes

     Hi Ian,

    Hope you are doing well. Are you using the LeDMXPro with internal memory cards by any chance? If so was there an option to self-install the cards?

    cheers,

    bonemap

    0
  • I
    Beta Platinum

    Hope you're all doing well as well! I am using the new ledmxpro that can accept sd cards. I haven't dis-assembled them yet to install one, but, its on the docket. In theory the SD cards are the the show fail-safe with a copy of the show stored and able to run controller free. I'll do a follow up post once that part either works or doesn't. 

    Ian

    0